Structural principle and daily inspection and maintenance of canned pump
- Categories:Technical Data
- Author:
- Origin:
- Time of issue:2022-04-13 11:02
- Views:
(Summary description)The structural principle of the canned pump is the same as that of the ordinary centrifugal pump, the difference lies in the drive motor. The motor of the canned pump is completely enclosed in the second layer of isolation sleeve or shielding sleeve, and the leakage prevention mainly depends on the internal anti-corrosion shielding sleeve. The shielding sleeve is sealed and welded to ensure that the stator winding and the rotor core are not immersed in the working liquid. The canned pump does not need to be lubricated with oil, and its bearings are lubricated by its own working fluid, which determines that the central shaft is a hollow shaft to facilitate the return of the lubricating working fluid. Inspection and maintenance of canned pump: 1. Daily inspection: ① Whether the pointer of the outlet pressure gauge is abnormal; ② Whether the current value is overloaded and abnormal; ③ Whether there is abnormal sound and vibration; ④ Pay attention to whether the bearing monitoring pointer is within the range of the red indicator; ; ⑥ whether there is liquid leakage. 2. Bearing sleep aid monitor The bearing monitor is mainly used to monitor the corrosion of the shielding sleeve and the wear of the bearing. The pointer of the monitor indicates the red area, indicating that the monitor contact is broken and the high pressure argon gas in the monitor leaks. It is caused by excessive wear of the bearing, and it is necessary to replace the monitor, bushing, thrust plate, bearing and eccentric nut, and the cost is 2600~2850 yuan; The wear of the shielding sleeve and the rotor shielding sleeve causes the motor to burn out. At this time, the maintenance cost is generally 20,000 to 30,000 yuan. 3. After the bearing exceeds the wear limit, it will cause the contact between the rotor shielding sleeve and the stator shielding sleeve, resulting in damage to the stator shielding sleeve, so pay close attention to the spot inspection of the bearing during operation. If the pump vibrates or has abnormal sound during operation, the pump should be disassembled, and the bearing should be checked. If the wear of the bearing and the shaft sleeve is found to be more than 0.3~0.5mm, it should be replaced according to the actual wear condition. From the actual operation situation, the general bearing wear is mainly radial, but the axial wear cannot be ignored. Check the axial wear mainly on the bearing and thrust plate. Even if the pump runs smoothly, regular inspections should be carried out, and the pump should be disassembled for regular inspections, mainly to check the wear of the bearings. The regular inspection period for canned pumps using domestic bearings is 3 months, and the inspection period for canned pumps using imported bearings is 6 months. The main points of canned pump maintenance: 1. Check the pump regularly, pay special attention to the monitor, and stop immediately if any abnormality is found. 2. The canned pump is lubricated by its own circulating flow, and it cannot be operated in shut-off, nor can it operate in reverse for more than 1 minute. 3. The throttling orifice plate is installed between the pump body outlet and the pipe flange, and is a stainless steel plate with a through hole smaller than the outlet pipe. Because the canned pump is lubricated by its own circulation, if there is no throttling effect of the throttling orifice, the pressure of the returning liquid will be very low. The bearing cannot be lubricated completely, resulting in bearing damage. In addition, the orifice plate can further increase the pressure. 4. The jacket is filled with cooling water to reduce the temperature of the equipment. When the temperature of the conveyed liquid is high, the jacket should be set. 5. Pay attention to the following points when assembling: Before installing the bearing into the bearing seat, put the lining into the incision on the periphery of the bearing, insert the bearing into the bearing seat, and screw the stop screw into the lining of the automobile accessories. Do not over-tighten it, otherwise it will easily cause early wear of the bearing; when installing the bearing seat, the recirculation hole of the front bearing seat has both the functions of exhaust and liquid drainage, and the recirculation hole should be aligned up and down, not flipped.
Structural principle and daily inspection and maintenance of canned pump
(Summary description)The structural principle of the canned pump is the same as that of the ordinary centrifugal pump, the difference lies in the drive motor. The motor of the canned pump is completely enclosed in the second layer of isolation sleeve or shielding sleeve, and the leakage prevention mainly depends on the internal anti-corrosion shielding sleeve. The shielding sleeve is sealed and welded to ensure that the stator winding and the rotor core are not immersed in the working liquid. The canned pump does not need to be lubricated with oil, and its bearings are lubricated by its own working fluid, which determines that the central shaft is a hollow shaft to facilitate the return of the lubricating working fluid.
Inspection and maintenance of canned pump:
1. Daily inspection: ① Whether the pointer of the outlet pressure gauge is abnormal; ② Whether the current value is overloaded and abnormal; ③ Whether there is abnormal sound and vibration; ④ Pay attention to whether the bearing monitoring pointer is within the range of the red indicator; ; ⑥ whether there is liquid leakage.
2. Bearing sleep aid monitor The bearing monitor is mainly used to monitor the corrosion of the shielding sleeve and the wear of the bearing. The pointer of the monitor indicates the red area, indicating that the monitor contact is broken and the high pressure argon gas in the monitor leaks. It is caused by excessive wear of the bearing, and it is necessary to replace the monitor, bushing, thrust plate, bearing and eccentric nut, and the cost is 2600~2850 yuan; The wear of the shielding sleeve and the rotor shielding sleeve causes the motor to burn out. At this time, the maintenance cost is generally 20,000 to 30,000 yuan.
3. After the bearing exceeds the wear limit, it will cause the contact between the rotor shielding sleeve and the stator shielding sleeve, resulting in damage to the stator shielding sleeve, so pay close attention to the spot inspection of the bearing during operation. If the pump vibrates or has abnormal sound during operation, the pump should be disassembled, and the bearing should be checked. If the wear of the bearing and the shaft sleeve is found to be more than 0.3~0.5mm, it should be replaced according to the actual wear condition. From the actual operation situation, the general bearing wear is mainly radial, but the axial wear cannot be ignored. Check the axial wear mainly on the bearing and thrust plate. Even if the pump runs smoothly, regular inspections should be carried out, and the pump should be disassembled for regular inspections, mainly to check the wear of the bearings. The regular inspection period for canned pumps using domestic bearings is 3 months, and the inspection period for canned pumps using imported bearings is 6 months.
The main points of canned pump maintenance:
1. Check the pump regularly, pay special attention to the monitor, and stop immediately if any abnormality is found.
2. The canned pump is lubricated by its own circulating flow, and it cannot be operated in shut-off, nor can it operate in reverse for more than 1 minute.
3. The throttling orifice plate is installed between the pump body outlet and the pipe flange, and is a stainless steel plate with a through hole smaller than the outlet pipe. Because the canned pump is lubricated by its own circulation, if there is no throttling effect of the throttling orifice, the pressure of the returning liquid will be very low. The bearing cannot be lubricated completely, resulting in bearing damage. In addition, the orifice plate can further increase the pressure.
4. The jacket is filled with cooling water to reduce the temperature of the equipment. When the temperature of the conveyed liquid is high, the jacket should be set.
5. Pay attention to the following points when assembling: Before installing the bearing into the bearing seat, put the lining into the incision on the periphery of the bearing, insert the bearing into the bearing seat, and screw the stop screw into the lining of the automobile accessories. Do not over-tighten it, otherwise it will easily cause early wear of the bearing; when installing the bearing seat, the recirculation hole of the front bearing seat has both the functions of exhaust and liquid drainage, and the recirculation hole should be aligned up and down, not flipped.
- Categories:Technical Data
- Author:
- Origin:
- Time of issue:2022-04-13 11:02
- Views:
The structural principle of the canned pump is the same as that of the ordinary centrifugal pump, the difference lies in the drive motor. The motor of the canned pump is completely enclosed in the second layer of isolation sleeve or shielding sleeve, and the leakage prevention mainly depends on the internal anti-corrosion shielding sleeve. The shielding sleeve is sealed and welded to ensure that the stator winding and the rotor core are not immersed in the working liquid. The canned pump does not need to be lubricated with oil, and its bearings are lubricated by its own working fluid, which determines that the central shaft is a hollow shaft to facilitate the return of the lubricating working fluid.
Inspection and maintenance of canned pump:
1. Daily inspection: ① Whether the pointer of the outlet pressure gauge is abnormal; ② Whether the current value is overloaded and abnormal; ③ Whether there is abnormal sound and vibration; ④ Pay attention to whether the bearing monitoring pointer is within the range of the red indicator; ; ⑥ whether there is liquid leakage.
2. Bearing sleep aid monitor The bearing monitor is mainly used to monitor the corrosion of the shielding sleeve and the wear of the bearing. The pointer of the monitor indicates the red area, indicating that the monitor contact is broken and the high pressure argon gas in the monitor leaks. It is caused by excessive wear of the bearing, and it is necessary to replace the monitor, bushing, thrust plate, bearing and eccentric nut, and the cost is 2600~2850 yuan; The wear of the shielding sleeve and the rotor shielding sleeve causes the motor to burn out. At this time, the maintenance cost is generally 20,000 to 30,000 yuan.
3. After the bearing exceeds the wear limit, it will cause the contact between the rotor shielding sleeve and the stator shielding sleeve, resulting in damage to the stator shielding sleeve, so pay close attention to the spot inspection of the bearing during operation. If the pump vibrates or has abnormal sound during operation, the pump should be disassembled, and the bearing should be checked. If the wear of the bearing and the shaft sleeve is found to be more than 0.3~0.5mm, it should be replaced according to the actual wear condition. From the actual operation situation, the general bearing wear is mainly radial, but the axial wear cannot be ignored. Check the axial wear mainly on the bearing and thrust plate. Even if the pump runs smoothly, regular inspections should be carried out, and the pump should be disassembled for regular inspections, mainly to check the wear of the bearings. The regular inspection period for canned pumps using domestic bearings is 3 months, and the inspection period for canned pumps using imported bearings is 6 months.
The main points of canned pump maintenance:
1. Check the pump regularly, pay special attention to the monitor, and stop immediately if any abnormality is found.
2. The canned pump is lubricated by its own circulating flow, and it cannot be operated in shut-off, nor can it operate in reverse for more than 1 minute.
3. The throttling orifice plate is installed between the pump body outlet and the pipe flange, and is a stainless steel plate with a through hole smaller than the outlet pipe. Because the canned pump is lubricated by its own circulation, if there is no throttling effect of the throttling orifice, the pressure of the returning liquid will be very low. The bearing cannot be lubricated completely, resulting in bearing damage. In addition, the orifice plate can further increase the pressure.
4. The jacket is filled with cooling water to reduce the temperature of the equipment. When the temperature of the conveyed liquid is high, the jacket should be set.
5. Pay attention to the following points when assembling: Before installing the bearing into the bearing seat, put the lining into the incision on the periphery of the bearing, insert the bearing into the bearing seat, and screw the stop screw into the lining of the automobile accessories. Do not over-tighten it, otherwise it will easily cause early wear of the bearing; when installing the bearing seat, the recirculation hole of the front bearing seat has both the functions of exhaust and liquid drainage, and the recirculation hole should be aligned up and down, not flipped.
Product Consultation:
Contact Email:
Company Address: